Wearlon® Super F-4        - Cement Floor Non-Stick Coating -

APPLICATION GUIDE AND TECHNICAL INFORMATION
Meets EPA, USDA, And FDA 21 CFR 175.300 Requirements

Surface Preparation

Wearlon® Super F-4 is a silicone-epoxy coating having unique release properties while adhering to a broad range of substrates including wood, concrete, fiberglass, metals, and most plastics including epoxies, polyurethanes, and alkyds.

Mixing Instructions

Wearlon® Super F-4 is a 2 component product. Component A must be mixed with a high shear mixer to ensure a homogenous coating. Wearlon® Super F-4 is packaged in 1 Gallon and 5 Gallon kit which contains the proper ratio of ingredients. The entire contents of each container should be mixed together.

For quantities less than the pre-packaged kit, mix as follows: To 15 parts of the A component, mix in 1 part of the B component. Mix the A and the B until completely blended. NO INDUCTION PERIOD NECESSARY...Spray or Roll immediately.

Thinning and Clean up

In most cases it is not necessary to thin Wearlon® Super F-4. If you find it necessary to thin Wearlon® Super F-4 you may add up to 5% DRINKING WATER. Clean up by using soap and water while Wearlon® Super F-4 is in an uncured state. For best results clean all equipment as soon as the application is complete. After the material has cured you will need to use solvents to remove the Wearlon® Super F-4

Application and Recoating

Spray or roll Wearlon Super F-4. Make sure the surface floor temperature is above 40°F before coating. Allow at least 12 hour curing before putting into service. Wearlon Super F-4 is manufactured to resist staining while allowing easy cleaning and therefore tends to be slippery. Most stains are simply wiped off or washed off with soap and water. For difficult stains such as spray paints use GRAFFITI OFF! cleaner followed by a subsequent washing with water. To reduce slip, sand or abrade the surface after coating dries and wipe down with Acetone. Shelf Life: 1 Year Storage: DO NOT FREEZE Caution - Extremely Slippery -care must be followed when walking on this surface to prevent slipping

Refer to Frequently Asked Questions (FAQs)
http://www.wearloncorp.com/index.php/faqs

Coating Type

Silicone/epoxy waterbased Color: Slate Gray Pot life: 60 min. @ 68°F Induction Time: None Solids: by Weight 49% Coverage Rate: Approx. 200 sq. ft. @ 3-4 mil DFT (85% Yield) Tensile Strength:>1750psi Elongation: ASTM 2370>5% Adhesion: ASTM D451>1000psi Abrasion: (CS 17/Kg/1000 cycles) <4 mg loss Cure Time: Complete in 5 days. Dry to the touch in 2 hours. Force cure 300°F for 30 min. Many applications can be returned to service the next day. VOC: ASTM 3960-1.0#/gl. Heat Resistance: Do not exceed 275°F continuous service

CAUTION: Wearlon® surfaces have a low coefficient of friction and therefore tend to be slippery.

To the best of our knowledge the technical data contained herein is true and accurate at the date of this issuance and is subject to change without prior notice. User must contact Wearlon® distributor/representative to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. Plastic Maritime guarantees its products to conform to Plastic Maritime quality control. Plastic Maritime assumes no responsibility for coverage, performance, or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY PLASTIC MARITIME, EXPRESSED OR IMPLIED, STATUTORY, BY OPERATION OF THE LAW OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FOR MORE INFORMATION CONTACT YOUR LOCAL DISTRIBUTOR OR CALL PLASTIC MARITIME AT 518-587-7624.