Wearlon Corporation

Plastic Maritime Corporation
Home What's New Products Test Data Data Sheets SDSs FAQs Ordering My Account Contact Us

Wearlon® 2020.99        - Interior Easy Clean Wall and Wood Coating -

APPLICATION GUIDE AND TECHNICAL INFORMATION
Meets EPA, USDA, And FDA 21 CFR 175.300 Requirements

Surface Preparation

Wearlon® 2020.99 is a silicone-epoxy top-coat, having unique release properties. It is supplied as a clear coating with excellent clarity and thus is ideal for over coating existing substrates without changing the overall appearance of the painted surfaces. Additionally, Wearlon® 2020.99 adheres to a broad range of substrates including metals. This silicone-epoxy is quite unique in that it can be coated over different surfaces including latex painted walls, resulting in protection of those surfaces from stains, adhesive tapes, and abrasion. Furthermore, Wearlon® 2020.99 can be readily re-coated, if desired, with conventional latex paints if one wants to change the color or repaint the surface.

Mixing Instructions

Before mixing, shake or stir each component until homogenous. Wearlon® 2020.99 is a 2 component product packaged in 1 Gallon and 5 Gallon kits which contain the proper ratio of ingredients. The entire contents of each container should be mixed together.

For quantities less than the pre-packaged kit, mix as follows: To 16 parts of the A component, mix in 2 parts of the B component. Mix the A and the B components until completely blended. Spray or roll immediately.

Thinning and Clean up

In most cases it is not necessary to thin Wearlon® 2020.99. If you find it necessary to thin Wearlon® 2020.99 you may add up to 5% DRINKING WATER. Clean up by using soap and water while Wearlon® 2020.99 is in an uncured state. For best results clean all equipment as soon as application is complete.

Application and Recoating

Product can be rolled, brushed or sprayed. For best results, spray Wearlon® 2020.99 with airless spray equipment. Conventional spray equipment works well and provides a slight orange peel finish. Wearlon® 2020.99 can also be applied by brush or roller, preferably a sponge roller or sponge brush for a smoother result.

CAUTION: Wearlon® 2020.99 will result in a Satin finish after application. Always keep a record or a sample of the original paint that was coated with Wearlon® 2020.99 in case there is a future need to duplicate any surfaces that might have been damaged.

Shelf Life: 1 Year Storage: DO NOT FREEZE

Refer to Frequently Asked Questions (FAQs)
http://www.Wearlon®corp.com/index.php/faqs

Coating Type

Silicone/epoxy waterbased Color: Clear Pot life: 8 hours @ 68°F Solids: by Weight 20% Coverage Rate: Approx. 1000 sq. ft. @ 1 mil DFT (85% Yield) Tensile Strength: >1750psi Elongation: ASTM 2370>5% Adhesion: ASTM D451>1000psi Abrasion: (CS 17/Kg/1000 cycles) <40 mg loss Cure Time: Complete in 1 day. Dry to the touch in 2 hours. VOC: ASTM 3960-0.7#/gl. Heat Resistance: Do not exceed 275°F continuous service

CAUTION: Wearlon® surfaces have a low coefficient of friction and therefore tend to be slippery.

To the best of our knowledge the technical data contained herein is true and accurate at the date of this issuance and is subject to change without prior notice. User must contact Wearlon® distributor/representative to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. Plastic Maritime guarantees its products to conform to Plastic Maritime quality control. Plastic Maritime assumes no responsibility for coverage, performance, or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY PLASTIC MARITIME, EXPRESSED OR IMPLIED, STATUTORY, BY OPERATION OF THE LAW OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FOR MORE INFORMATION CONTACT YOUR LOCAL DISTRIBUTOR OR CALL PLASTIC MARITIME AT 518-587-7624.

Wearlon Corporate Site
Copyright 2002-2017 Plastic Maritime Corporation. All rights reserved.
Wearlon Trademark (Plastic Maritime Corporation) Reg. No. 3,193,635
Patents: 6,312,777 / 6,153,304 / 6,120,849 / 6,086,995 / 6,084,020 / 6,057,276 /
5,935,692 / 5,929,005 / 5,910,535 / 5,814,402 / 5,736,249 / 5,707,472
Questions or comments? Contact us.
Web site designed and hosted by St. Kolbe Networking.
0.0