Wearlon Corporation

Plastic Maritime Corporation
Home What's New Products Test Data Data Sheets SDSs FAQs Ordering My Account Contact Us

Data Sheet for Wearlon 2020.90        - Primer - Protective Coating -

APPLICATION GUIDE AND TECHNICAL INFORMATION
Meets EPA, USDA, And FDA 21 CFR 175.300 Requirements

Surface Preparation

Wearlon® 2020.90 is a silicone-epoxy having unique adhesion properties to a broad range of substrates. The adhesion properties, excellent elongation and water resistance properties make it ideal for a protective coat or a primer coat. Proper substrate treatment is sometimes necessary prior to application. (Steel: SSPC 7, a brushed-off blast cleaned surface. Aluminum: SSPC 7. Concrete: Power wash, removing oil residue.)

Mixing Instructions

See Application Guide.

Before mixing, shake or stir each component until homogenous.

Wearlon® 2020.90 is a 2 component product packaged in 1 Gallon and 5 Gallon kit which contain the proper ratio of ingredients. The entire contents of each container should be mixed together.

For quantities less than the pre-packaged kit, mix as follows: To 11 parts of the A component mix in 2 parts of the B component. Mix the A and the B until completely blended.

NO INDUCTION PERIOD NECESSARY... Spray or Roll immediately.

Thinning and Clean up

In most cases it is not necessary to thin Wearlon® 2020.90. If you find it necessary to thin Wearlon® 2020.90 you may add up to 5% DRINKING WATER. Clean up by using soap and water while Wearlon® 2020.90 is in an uncured state. For best results clean all equipment as soon as the application is complete. After the material has cured you will need to use solvents to remove the Wearlon® 2020.90

Application and Recoating

Product can be rolled, brushed or sprayed. For best results, spray Wearlon® 2020.90 with airless spray equipment. Conventional spray equipment works well and provides a slight orange peel finish. For a greater orange peel effect apply Wearlon® 2020.90 with a short nap Mohair roller or Urethane foam roller. Roll 1 coat, and then follow within 30-45 min. with the 2nd coat to achieve your total mil thickness.

FLASH RUSTING can be readily eliminated by applying a mist coat of Wearlon® 2020.90 using spray or a foam roller for less than a 1 mil wet deposit. Curing this light deposit of 2020.90 prior to any subsequent Wearlon coating will eliminate flash rusting. Applying Wearlon to a warm surface, 100°F to 140°F will eliminate flash rusting while speeding up the cure of the coating.

Shelf Life: 1 Year Storage: DO NOT FREEZE

Refer to Frequently Asked Questions (FAQs)
http://www.wearloncorp.com/index.php/faqs

Coating Type

Silicone/epoxy waterbased Color: Various (contact Wearlon® representative) Pot life: 60 min. @ 68°F Induction Time: None Solids: by Weight 49% Coverage Rate: Approx. 200 sq. ft. @ 3-4 mil DFT (85% Yield) Tensile Strength: >1750psi Elongation: ASTM 2370>10% Adhesion: ASTM D451>1000psi Abrasion: (CS 17/Kg/1000 cycles) <40 mg loss Cure Time: Complete in 5 days. Dry to the touch in 2 hours. Force cure 300°F for 30 min. Many applications can be returned to service the next day. VOC: ASTM 3960-1.2#/gl. Heat Resistance: Do not exceed 275°F continuous service

CAUTION: Wearlon® surfaces have a low coefficient of friction and therefore tend to be slippery.

To the best of our knowledge the technical data contained herein is true and accurate at the date of this issuance and is subject to change without prior notice. User must contact Wearlon® distributor/representative to verify correctness before specifying or ordering. No guarantee of accuracy is given or implied. Plastic Maritime guarantees its products to conform to Plastic Maritime quality control. Plastic Maritime assumes no responsibility for coverage, performance, or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY PLASTIC MARITIME, EXPRESSED OR IMPLIED, STATUTORY, BY OPERATION OF THE LAW OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FOR MORE INFORMATION CONTACT YOUR LOCAL DISTRIBUTOR OR CALL PLASTIC MARITIME AT 518-587-7624.

Wearlon Corporate Site
Copyright 2002-2024 Plastic Maritime Corporation. All rights reserved.
Wearlon Trademark (Plastic Maritime Corporation) Reg. No. 3,193,635
Patents: 6,312,777 / 6,153,304 / 6,120,849 / 6,086,995 / 6,084,020 / 6,057,276 /
5,935,692 / 5,929,005 / 5,910,535 / 5,814,402 / 5,736,249 / 5,707,472
Questions or comments? Contact us.
Web site designed and hosted by St. Kolbe Networking.
0.0